DG201ABK DATASHEET PDF

DGABK datasheet, DGABK pdf, DGABK data sheet, datasheet, data sheet, pdf, Intersil, Quad SPST, CMOS Analog Switches. DGABK Datasheet, DGABK PDF, DGABK Data sheet, DGABK manual, DGABK pdf, DGABK, datenblatt, Electronics DGABK. DGABK datasheet, DGABK circuit, DGABK data sheet: MAXIM – Quad SPST CMOS Analog Switches,alldatasheet, datasheet, Datasheet search site.

Author: Gogul Nidal
Country: Botswana
Language: English (Spanish)
Genre: Travel
Published (Last): 23 October 2017
Pages: 117
PDF File Size: 8.1 Mb
ePub File Size: 16.12 Mb
ISBN: 325-9-44016-492-8
Downloads: 85246
Price: Free* [*Free Regsitration Required]
Uploader: Ditaxe

Dambar protrusions shall not exceed 0. SR Datasheet – Micropower Direct. B1 maximum dimensions do not include dambar protrusions.

DGA Intersil Quad SPST, CMOS Analog Switches ChipFind Datasheet Archive |

Measure dimension S1 at all four corners. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Asa cum sunt, la Tine vin! The DGA has a maximum turn-off time of ns and a maximum turn-on time of ns. A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. The algebraic convention whereby the most negative value is a minimum, and the most positive value is a maximum, is used in this data sheet.

In case of conflict between English and Metric dimensions, the inch dimensions control. In either case, source-to-body diodes can be forward biased and conduct current from the signal source. For more information on TYP values see Note 3.

  JAMICON TK PDF

For information regarding Intersil Corporation and its products, see www. For the latest package outline information, go to www. These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. Limit diode current to maximum current ratings. E and eA are measured with the leads constrained to be perpendicular to datum -C. Dimension Q shall be measured from the seating plane to the base plane. For this configuration dimension b3 replaces dimension b2.

Device mounted with all leads soldered to PC board. The DG has a maximum turn-off time of ns and a maximum turn-on time of ns.

Datasheet «DG201A»

All Rights Reserved All other trademarks mentioned are the property of their respective owners. Feedthrough via gate capacitance may result in spikes at leading and trailing edge of output waveform.

Package Information continued The package drawing s in this data sheet may not reflect the most current specifications. Copyright Intersil Americas Inc. N is the maximum number of terminal positions. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

Dimension M applies to lead plating and finish thickness. This dimension allows for off-center lid, meniscus, and glass overrun. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied.

  BRISBANE REFIDEX PDF

Mold flash or protrusions shall not exceed 0. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Typical values are for design aid only, not guaranteed and not subject to production testing. Pin Configurations continued To provide protection for overvoltages up to 20V above the supplies, a 1N or 1N type diode should be placed in series with the positive and negative supplies as shown in Figure 2.

The addition of these diodes will reduce the analog signal range to 1V below the positive supply and 1V above the negative supply.

DG211 Datasheet PDF

Maxim reserves the right to change the circuitry and specifications without notice at any time. When the enable input is high, a channel is selected by the address inputs, and when low, all channels are off. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. No circuit patent licenses are implied. For more information on TYP values see Note 2.

Maxim guarantees that these switches will not latch up if the power supplies are disconnected with input signals still connected.

Author: admin