Find the most up-to-date version of ASTM E at Engineering Macroetching, also known as deep etching, involves etching specimens prepared with a suitable acid or reagent for macrostructural examination. Contact us. Purchase your copy of ASTM E – 17 as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards available.
|Published (Last):||19 January 2016|
|PDF File Size:||15.42 Mb|
|ePub File Size:||12.54 Mb|
|Price:||Free* [*Free Regsitration Required]|
In the case of forgings, depending upon prior agreement, this may be accomplished by adding excess metal for discard on the ends or ends of the forging; or, by forging in multiple lengths and removing the test disk between individual pieces when cutting up the multiple forging. Examination of Ingot Cast Product Specimens 9. The method employs the action of an acid or other corrosive agent to develop the macrostructural characteristics of a suitably prepared specimen.
Evaluation of machined parts for grinding cracks in tools and dies. Sufficient torch cut material should be removed by cold cutting to eliminate the thermal effects of torch cutting. The etching solution should be clear and free from scum. NOTE 1—The addition of hydrogen peroxide H2O2 may be necessary in order to provide sufficient reaction to properly etch some types of product.
Add acid slowly to water with stirring. Search book title Enter keywords for book title search. The usual procedure is to take a roughing cut, then a? Billets or blooms going into small sizes are sampled after the initial breakdown. Random sampling of the?
ASTM E – 17 – Standard Method of Macroetch Testing Steel Bars, Billets, Blooms, and Forgings
The best time for examination is immediately after drying. If you like to setup a quick demo, let us know at support madcad. Establishment of general standards for acceptance or rejection for all conditions is impractical as some conditions must be considered relative to the part in which it occurs.
If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
ASTM E – 17 Standard Method of Macroetch Testing Steel Bars, Billets, Blooms, and Forgings
Remember me for one awtm. The specimens may be placed directly into the solution, but the best practice is to place the specimen in corrosion-resistant baskets or on corrosion-resistant supports, such as glass rods underneath the specimen to raise it off the bottom of the dish. Today, some 12, ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence.
Copyright Compu-tecture, Inc. See Test Method E for other etching solutions.
ASTM E381 – 17
Etching times with cold solutions see 5. Asfm standard is subject to revision at any time by the responsible technical committee and must be reviewed every?
Macroetch Examinations Macroetching, also known as deep etching, involves etching specimens prepared with a suitable acid or reagent for macrostructural examination at low magnifications and rating by a grades series of photographs showing the incidence of certain conditions such as: Sharp tools are necessary to produce a good ee381.
The specimen should not be blotted dry.
The most common reagent for macroetching iron and steel is a 1: After the smut is removed, rinse the specimen under hot running water e31 blow it dry with compressed air. Maintain a sufficient volume of solution in the vessel to cover the specimen with a layer of at least 25 mm 1 in.
The sectioning of the large specimens should be done so as not to disturb the central portion of the section. These may be located anywhere from the near surface region of the product to the center of the product, astmm on the source and asstm of the condition. Any method of preparing smooth surfaces with a minimum amount e31 cold work should be satisfactory. The hydrochloric acid need not be reagent grade.
Significance and Use 4. Other rating methods may be established per f381 between the user and producer. Click here to request a quote. Study of weld structures, definition of weld penetration, dilution of filler metal by base metals, entrapment of flux, porosity, and cracks in weld and heat affect zones, etc.
Macroetching, also known as deep etching, involves etching specimens prepared with a suitable acid or reagent for macrostructural examination at low magnifications and rating by a grades series of photographs showing the incidence of certain conditions such as: The name implies that the etched surface is examined visually, or at low magni?
The reagent should be used under a fume hood, or some other means of carrying off the corrosive fumes must be provided. Grinding, which also may be used, is usually conducted in the same manner, using free-cutting wheels and light feeds. Development of grain flow in a forged part or fastener, which is a critical property for the integrity of the forging. Sulfur printing shall be performed in accordance with Practice E